Тест складається із 80 випадкових питань.
Усього питань на цю тему: 108
On area A4 the function “Transmission and reception of signals for locating” is mainly based on:
The use of SARSAT COSPAS Epirbs.
The use of SART transponders.
The carriage of a new Noxious Liquid Substance not yet listed in the IBC Code may be considered possible, provided it is achieved through a “tri-partite” agreement between:
The Flag State of the Shipper/the Flag State of the Charterer/the Flag State of the Receiver.
The IMO/the Port State of the Shipper/the Port State of the Receiver.
The Port State of the Shipper/the Flag State of the Carrier/the Port State of the Receiver.
The Shipper/the Receiver/the Operator or Charterer.
As per MARPOL 73/78, coal slurry, clay slurry, dextrose solution and molasses are classified as:
DG placards shall be located on a freight container:
One of the back end and one on one of the sides (only).
One on each end and one on each side.
The steps of the embarkation ladder used must be spaced apart by a distance of:
Equally spaced, not less than 200 mm or more than 280 mm.
Equally spaced, not less than 300 mm or more than 380 mm.
A tug is connected to the bow of a vessel. Will the force exerted by it be the same at any ahead speed?
No, on the bow the tug uses power to run with the vessel, which reduces the available power on the towline.
No, when the ahead speed of the ship increases the force exerted by the tug will also increase.
Yes, the force would normally be expected to be the same at any speed of the ship.
What rules and regulations are regulating the watch keeping routines in the engine room?
Both STCW and Class rules.
International Standard for Training and Watch keeping (STCW).
What type of dynamic forces may cause indent in plating on forecastle deck and main deck in way of pillars inside forecastle?
Pressure forces caused by green water on deck.
Impact pressure forces in way of abrupt or flared bow.
Forces created by waves on the forecastle.
Slamming in way of flat bottom forward of light draught.
On all UMS operated vessels and also on most other vessels the engine room is equipped with fire detectors. What requirements of testing and checking of the detectors are to be observed?
All the mentioned alternatives.
When testing detectors by suitable equipment (smoke and heat) check that the sensors self controlling system, e. g. a flashing control light etc. is functioning.
Check that the actual detector is giving appropriate signals to the central control unit and that all electric connections are in good order.
Check the detector with heat and/or smoke (in accordance with instructions in its manual).
How often must inspection of proper working of the EPIRB’s and SART’s take place on board? Once per:
To maintain good relationship among the crew on board a vessel, one must be:
Understanding, Co-operative, and have respect from both sides.
Give authority to others.
Polite and diplomatic while talking to crew members.
Strict and authoritative while giving orders.
A cargo pumproom or other enclosed space which contains cargo handling equipment on a chemical tanker shall be fitted with a mechanical ventilation system, capable of being controlled from outside the space. What is the minimum number of atmosphere changes per hour, based on the total volume of the space, that such a system must deliver?
Not less than 10 charges per hour.
Not less than 30 charges per hour.
There is no specified minimum number of changes, provided it is running continuously throughout any cargo operation.
If the ventilation is permanent, it shall deliver at least 20 changes per hour; if it involves part recirculation, then it shall deliver at least 30 changes per hour.
Ballast introduced into a cargo tank on a chemical tanker which has been washed to such an extent that the ballast contains less than 1 ppm of the substance previously carried may be discharged into the sea without regard to the discharge rate, ship’s speed and discharge outlet location, but under certain conditions, which require:
Provided the ship is underway and a sample of the ballast water has been drawn from the tank and is stored on board, there are no additional conditions to be imposed on such a discharge.
That the vessel is not less than 50 miles from the nearest land and is proceeding on route.
That the vessel is not less than 12 miles from the nearest land and is in water that is not less than 25 metres deep.
That the discharge is passed through the Oil Discharge Monitoring Equipment and a visual watch is maintained on the vessel’s wake.
Not less than one and a half times its specified maximum working pressure, but not more than two-fifths of its bursting pressure.
Not less than one and a half times its specified maximum working pressure, but not more than two-fifths of its bursting pressure.
2 times its designed working pressure, but not more than three-fifths of its nominal bursting pressure.
Not less than one and a half times its nominal bursting pressure, but not more than four-fifths of its specified maximum working pressure.
Not more than one and a half times its specified maximum working pressure, but not less than two-fifths of its bursting pressure.
Under what convention is the master to ensure that a ship is seaworthy and in a fit state to safely carry a shipper’s cargo?
Inmarsat Telex Service code “33” can be used:
When technical problems are experienced with the Inmarsat-terminal.
To ask for maritime enquiries.
When the coast-station is disfunctional.
The Training Manual shall contain instructions and information on the life-saving appliances and the best method of survival. The training manual shall contain detailed explanations of crew duties in relation to emergency situations. Which of the following tasks or duties shall be included in the manual according to present regulations?
The use of the ship’s line throwing apparatus.
The use of escape routes and other escape methods.
The use of surface to air visual signals to be used by survivors.
The use of navigational equipment for survival crafts.
Which of the following is a coast station MMSI?
The mode J2B is used:
For radiotelex-traffic in the MF/HF band between the ship and shore stations.
For telephone traffic in the MF/HF bands between ship and shore stations.
For urgent message transmitting and receiving.
For how long time must the printout from the Oil Discharge Monitoring Equipment (ODME) be retained onboard?
A cofferdam, a pumproom or an empty tank, located between cargo tanks containing cargoes or cargo residues which might react with each other in a hazardous manner, are all acceptable methods of segregation in chemical tanker stowage according to the IBC Code. For this purpose, it may also be acceptable to have:
A common bulkhead, provided it overlaps for less than 15 % of the length of the bulkhead on the larger tank.
A common bulkhead, provided it is at least 10 mm thick.
An intervening cargo tank containing a mutually compatible cargo or cargo residues.
A cruciform joint, separating two tanks diagonally.
On board an accident happened. Urgent radio-medical advice is needed. We choose the category:
The relay of a distress-call by an RCC for coast-station begins with:
Give the meaning of the following symbol:
Survival craft distress pyrotechnic signals.
The “dew point” of a liquid chemical can be defined as:
The temperature at which dry-ice melts in Acetone.
The temperature at which a condensable component is saturated with respect to a gas, as in operational terms is seen at the point when moisture no longer detectable in air.
The temperature at which a saturated as exhibits condensation.
The temperature at which a gas is saturated with respect to a condensable component, as in operational terms is seen at the point when air is saturated with moisture.
What are the three volumes of the IAMSAR Manual?
I – Organization and Management II – Mission Co-ordination III – Mobile Facilities.
I – Planning and Preparation II – Rescue III – Reference.
A – Command and Control B – Communications C – Rescue Procedures.
I – Organization II – Communications III – Rescue Procedures.
Onboard training should be organised in such a way that:
It is an integral part of the overall training plan.
Each crew member is trained individually.
It does not contravene with the rest hours of the crew.
How often shall crew members participate in fire drills?
What is the probable cause of an error in the position shown on a GPS receiver set into “2D” fixing?
Incorrect height of the antenna set into the receiver.
The receiver has defaulted to “3D” fixing and there is no overhead satellite.
The limit set on the HDOP figure is too great.
The limit set on the VDOP figure is too small.
Testing a SART is permitted:
Only at sea, outside territorial waters.
Only in a port or harbour.
At sea, outside territorial waters, and in a port or harbour.
The time indication 121310z means in maritime radio communication:
12th day, 13:10 hours UTC.
12th month, 13:10 hours UTC.
12th day, 13:10 hours local time.
12th month, 13th day, 10:00 hour local time.
It is the Master’s responsibility to ensure that:
Concerned personnel carry out the onboard training programme effectively.
Life jackets are worn during every training.
All information regarding the onboard training is given to the ship manager.
Safety equipment is not used during the training.
How would you determine whether a particular cargo transfer hose was compatible with the chemical product to be transferred?
Check the product classification mark stamped on the flange collar of the hose.
Check the colour of the hose against the general classification code in the IBC Code.
Refer to the product entry in the hose manufacturer’s chemical resistance chart.
There will be no need to check. If the hose has been supplied to a chemical tanker, it will have been certified for the transfer of all chemical products.
If your chemical tanker is equipped with high velocity venting valves, at what minimum height above the weather deck or catwalk should they be installed?
With respect to the ISM, what training in addition to lifeboat and fire drills must be carried out?
Familiarization, and other drills identified as necessary by the ship.
The boat drill and fire drill should be adequate to meet your needs.
A small vessel with a right handed propeller and no thruster is approaching a berth with an onshore wind. What is the best way to have a controlled berthing?
Dredge a forward anchor, working the engine and rudder against it to keep the stern up.
Reduce speed by going full astern on the engines.
Stop the engine and let the vessel momentum and the wind drop the vessel onto the berth.
Full starboard rudder and stop engines.
For security purposes, the IMDG Code should be read in conjunction with the:
Chapter XI-2 of SOLAS and Part A of the ISPS Code.
IMO NVIC 24 and 46 CFR 2.05.
Chapter V of SOLAS and Annex II of MARPOL.
Part B of the ISPS Code and Chapter II of the Maritime Transport and Offshore Facilities Act.
Which of the following requirements regarding on board stability data corresponds to present regulations? (NSCL 4/12.1).
Drawings and calculations documenting the stability of the ship, both in intact and all possible damage condition.
A calculation example showing the use of “KG” limitation curves.
A calculation example showing use of “GM” limitation curves.
Stability data produced by stability calculation instruments.
Your vessel is approaching a port in restricted visibility and you hear this signal. What kind of vessel is it and what is it doing?
It comes from a vessel engaged in pilotage duties and it is making way through the water.
It comes from a vessel restricted in her ability to manoeuvre.
It comes from a vessel at anchor, less than 100 metres in length.
It comes from a vessel engaged in pilotage duties at anchor, over 100 metres in length.
The compensation payment by the charterer that is due when a vessel is unable to load / discharge her cargo within the allowed and contracted time is referred to as:
Contractual penalty discount.
The minimum permissible distance measured horizontally between the ship’s shell plating and the outer side bulkhead of the first cargo compartment on a type II chemical tanker is:
Not less than moulded breadth/15.
Not less than moulded breadth/5.
A SART is used by a vessel in distress. This SART is seen on the screen of a:
Both 3 Cm and 10 Cm radar.
Your vessel is involved in a collision with another vessel. What should you as Master tell the Master on the other vessel?
There should be no communication with the other vessel.
Explain your actions prior to the collision and request details of actions taken by the other vessel which resulted in the collision.
Name; Port of registry; Port of destination of your vessel.
Ask if there is any assistance required by the other vessel.
You are carrying a bulk cargo of Phosphoric Acid. Which components of the cargo pumps may be damaged as a result of discharging this particular cargo and why?
The cargo seals may be damaged from the abbrasive effect of any sediment.
The valves in the associated piping may be distorted by pressure surges created by cavitation as the acid is discharged.
The outer casing may be corroded by the unstable impurities within the acid.
The impeller veins may be damaged as a result of the relatively high density of the cargo if the pumps are run at too high a speed.
A MF/HF-DSC multi-frequency call attempt may:
Be repeated after 1 to 1 and a half minutes.
Be repeated after 3 and a half to 4 and a half minutes.
You can reduce the need for security guards in certain areas by installing:
As per the IMDG Code, “Marine Pollutant” is defined as:
A substance which is subject to the provisions of Annex III of MARPOL.
Any substance which is deemed hazardous to the marine environment.
A substance which is subject to the provisions of Chapter V of SOLAS 1974, as amended.
Under what convention is the master to ensure that a ship is seaworthy and in a fit state to safely carry a shipper’s cargo?
How can an ARPA best assist the bridge team to steer a suitable course to make good the entrance to a channel?
Alter course so that own-ships ground stabilised true vector passes through the entrance to the channel.
Alter course so that own-ships water stabilised true vector passes through the entrance to the channel.
Use the mapping facility provided by the ARPA, create a map of the channel then display it for entry.
The “dew point” of a liquid chemical can be defined as:
The temperature at which a gas is saturated with respect to a condensable component, as in operational terms is seen at the point when air is saturated with moisture.
The temperature at which a saturated gas exhibits condensation.
The temperature at which dry-ice melts in Acetone.
The temperature at which a condensable component is saturated with respect to a gas, as in operational terms is seen at the point when moisture no longer detectable in air.
What is a Declaration of Security?
A checklist jointly completed by the ship and shore security representatives.
A document stating the ship’s security level.
A document between the port and the cargo owner stating security.
A checklist jointly completed by the Ship Security Officer and the US Coast Guard.
Noxious Liquid Substances which, if discharged into the sea from tank cleaning or deballasting operations, are deemed to present a hazard to either marine resources or human health or cause harm to amenities or other legitimate uses of the sea and therefore justify a limitation on the quality and quantity of the discharge into the marine environment. Such substances are:
A category “Y” substance as identified in the revised MARPOL Annex II.
A category “X” substance as identified in the revised MARPOL Annex II.
An NLS as defined in ISGOTT revision V.
A liquid cargo that is prohibited for carriage in vessels other than type 1 chemical tanker, as defined in the INC Code.
“Passivation” is a restorative process periodically applied to stainless steel tanks on a chemical tanker. What effect does this process have on the steel surface?
It restores and reforms the passive Chromium Hydroxide surface layer.
It restricts active corrosion on the surface steel.
It causes a chemical reaction, which produces a new inert Chromium Oxide layer on the surface of the steel.
It restores the surface steel to an even and smooth finish, thereby encouraging drainage during discharge.
MARPOL 73/78 defines a “high viscosity substance” as:
A noxious liquid substance in category “X” or “Y” with a viscosity equal to or greater than 50 mPa·s at the unloading temperature.
A noxious liquid substance of any category with a pour point of greater than 37,8 °C.
Any noxious liquid substance, the residues of which cannot be stripped from a cargo compartement and its associated piping and pumping system to equal to or less than 75 litres.
A noxious liquid substance in category “Y” with a viscosity equal to or greater than 100 mPa·s at 37,8 °C.
A “Standard Format for Search and Rescue Situation Reports” (SITREPs) should be used by vessels in distress. The SITREP can be compiled as a short form (urgent essential details). Which of the following information shall be included when using the “short form”?
The mode J2B is used:
For radiotelex-traffic in the MF/HF band between the ship and shore stations.
For urgent message transmitting and receiving.
For telephone traffic in the MF/HF bands between ship and shore stations.
How is a Safety Management Certificate obtained?
Ship owners has Document of Compliance issued, and vessel is assessed and holds all statutory certificates.
Ship owner is authorised to carry out internal audits and issue SMC.
Vessel is surveyed by MCA and certificate issued.
RSS issue SMC with Register.
As per SOLAS regulations, the general emergency alarm system must be tested:
What signal may be given by sound and by light to indicate that a vessel fails to understand the intentions or actions of another vessel, or is in doubt that sufficient action is being taken by the other to avoid collision?
One prolonged blast (flash), followed by five or more short and rapid blasts (flashes).
Five short and rapid blasts (flashes).
Three short and rapid blasts (flashes).
Five prolonged blasts (flashes).
What action should be taken by the Officer of the Watch if someone reports a fire to them?
Send the bridge look-out down to investigate.
Stop engines and inform the engine room.
To inform ship of coast-stations messages, coast stations give a fixed times:
A traffic list with the call-sign of the ships involved in alphabetical numerical sequence.
A list of the official identification numbers, for example the Maritime Mobile Service Indentity (MMSI).
A list with the names of the ships involved spoken alphabetical numerical sequence.
A list of all the messages for each vessel.
When using an ENC chart to passage planning, why should a scale at or near its compilation scale always be used?
The chart detail is correct for its usage band.
It is only at this scale that a route can be plotted.
That is incorrect, as any ENC can be zoomed in or out for passage planning.
It is only at this scale that route validation is possible.
The authority to order the use of distress signal or distress alerts is:
The first person to discover the distress situation.
The person designated to maintain communication during distress situations.
As a result of being in collision with your vessel, the other vessel is involved is on fire. What are your responsibilities?
The other vessel is in distress and if possible I will render assistance.
You should continue on with the voyage if your damage is not serious.
There is no statutory requirement to provide assistance as the actions of that vessel were the primary cause of the collision.
Your vessel should manoeuvre close to the other vessel and aid the fire-fighting operation.
With what system is a NAVTEX-message transmitted?
Which one of the listed requirements regarding the stowage of lifeboats and life-rafts corresponds to present SOLAS regulations?
Lifeboats shall be stowed attached to launching appliances.
Life-rafts intended for throw-overboard launching shall be stowed midships secured to means for transfer to either side.
Life-rafts shall be stowed close to the stern of the vessel.
Davit-launched life-rafts shall be stowed on starboard side of the ship.
You are on a vessel 10 nautical miles off the coast of Nigeria, West Africa. Are you allowed to dump empty glass bottles overboard?
No, glass bottles can not be dumped overboard.
Yes, glass bottles can be dumped overboard.
Yes, the bottles can be dumped if they are ground so that the resulting particles can pass through a screen with 50 mm openings.
Hand flares and buoyant smoke signals can continue to burn or emit smoke after having been immersed for a period of 10 s:
Right if the immersion depth is smaller than 1 m.
Right if the immersion depth is smaller than 100 mm.
If all indications are that a cargo has been received without damages, irregularities or short shipment and the phrase “apparent good order and condition” is entered on the Bill of Lading, then this Bill is this said to be:
An endorsed Bill of Lading.
A Due Title Bill of Lading.
A Bill of Lading completed for shipment.
Under most circumstances, how will communication be carried out between a ship and a SAR helicopter?
How often shall each member of the crew participate in an “abandon ship”-drill?
If the shipper wishes to ensure that a vessel or her operators will not be held responsible for any damage that may arise from the carrier issuing a clean Bill of Lading, even though the Mate’s receipt is marked as “unclean”, such a document is called the:
An addendum to the Bill of Lading.
An absolution clause in the shipping documents.
Which of the following requirements regarding life-buoys correspond to present regulations? (SOLAS III/7.1).
All life-buoys shall be placed in holders with quick-release arrangement.
Not less than half the total number of lifebuoys shall be provided with self-igniting lights.
At least one lifebuoy shall be placed within the vicinity of the stern.
At least one life-buoy on each side of the ship shall be fitted with a buoyant lifeline.
What type of dynamic forces may cause indent in plating on forecastle deck and main deck in way of pillars inside forecastle?
Forces created by waves on the forecastle.
Slamming in way of flat bottom forward of light draught.
Pressure forces caused by green water on deck.
Impact pressure forces in way of abrupt or flared bow.
To what pressure will a new length of cargo hose be tested by a manufacturer prior to its supply to a vessel for service onboard a chemical tanker?
Not less than one and a half times its nominal bursting pressure, but not more than four-fifths of its specified maximum working pressure.
Not less than one and a half times its specified maximum working pressure, but not more than two-fifths of its bursting pressure.
2 times its designed working pressure, but not more than three-fifths of its nominal bursting pressure.
Not more than one and a half times its specified maximum working pressure, but not less than two-fifths of its bursting pressure.
One of the sailors needs urgent medical assistance. The VHF-call starts with:
To maintain good relationship among the crew on board a vessel, one must be:
Understanding, Co-operative, and have respect from both sides.
Strict and authoritative while giving orders.
Give authority to others.
Polite and diplomatic while talking to crew members.
Which option best completes the following statement? The version of the IHO presentation library on the ECDIS is important because:
If it is not the latest version, the ECDIS will not be compliant.
It is where the files for maintenance of the system software are stored.
It influences the colours on the display.
It allows ECDIS to decide on the scale setting of the chart.
Which personnel must undergo familiarization training on board?
During an audit, adherence to the company cargo handling procedures can best be demonstrated:
By providing a summary of out-turn figures for the auditor.
By requesting that an audit takes place during cargo operations.
By providing a summary of incident and lost time figures for the auditor that reflects a successful and trouble-free system on board.
By being able to provide comprehensive and verifiable documentary records of cargo operations.